Fabrication of Cu/graphite film/Cu sandwich composites with ultrahigh thermal conductivity for thermal management applications

Effective thermal management of electronic integrated devices with high powder density has become a serious issue, which requires materials with high thermal conductivity (TC). In order to solve the problem of weak bonding between graphite and Cu, a novel Cu/graphite film/Cu sandwich composite (Cu/GF/Cu composite) with ultrahigh TC was fabricated by electro-deposition. The micro-riveting structure was introduced to enhance the bonding strength between graphite film and deposited Cu layers by preparing a rectangular array of micro-holes on the graphite film before electro-deposition. TC and mechanical properties of the composites with different graphite volume fractions and current densities were investigated. The results showed that the TC enhancement generated by the micro-riveting structure for Cu/GF/Cu composites at low graphite content was more effective than that at high graphite content, and the strong texture orientation of deposited Cu resulted in high TC. Under the optimizing preparing condition, the highest in-plane TC reached 824.3 W·m⁻¹·K⁻¹, while the ultimate tensile strength of this composite was about four times higher than that of the graphite film.     

混炼方式对螺旋纳米碳纤维增强天然橡胶复合材料力学性能的影响

采用干法和湿法两种混炼工艺制备了螺旋纳米碳纤维(HCNFs)/炭黑(CB)/天然橡胶(NR)复合材料,通过扫描电镜、拉伸试验机和应变扫描仪分别对所制备复合材料的界面形貌、力学性能和Payne效应进行了测试分析,考察了混炼方式对复合材料宏观力学性能及Payne效应的影响。结果表明,与纯CB填料相比,在干湿两种混炼方式下,添加适量的HCNFs(1～6份)能提高HCNFs/CB/NR复合材料的300%定伸应力、扯断伸长率、拉伸强度和硬度。与干法混炼相比,湿法混炼能明显增强HCNFs/CB/NR复合材料的Payne效应,并提升在HCNFs高添加量(2～6份)条件下的拉伸强度和扯断伸长率,这主要源于湿法混炼能够有效改善HCNFs在橡胶基质中的分散性。     

超精密气体静压系统节流器法向随机微振动研究

以无气腔平面节流器为研究对象,对节流器流固耦合法向随机微振动进行了理论仿真和实验研究。受限于节流器厚度与气膜厚度尺寸的差异和输入初始边界条件,建立了节流器的COMSOL仿真简化模型,对节流器-气膜微流场进行双向流固耦合数值模拟。仿真结果表明,节流器的法向随机微振动幅值关于节流器中心对称,且由中心向边缘逐渐增大;微振动幅值随气体入口流速的增大而增大。实验采用纳米级激光测振仪,依次测量供气压力为0.1,0.2,…,0.5 MPa时尺寸为75 mm×50 mm×14 mm的HEXAGON双环联结型节流器多个不同位置的法向振动,实验结果表明,法向随机微振动幅值分布特性与仿真结果一致,关于节流器中心对称,且由中心向边缘逐渐增大,验证了节流器法向微振动的"跷跷板"振动形式;在0.5 MPa供气压力下,边缘振动幅值超过1 nm。对实验数据进行功率谱密度分析,结果表明不同供气压力下法向随机微振动均在9.4 kHz和10.6 kHz处产生较大功率,可认为与节流器-气膜流固耦合系统的固有频率有关。研究结果有效地揭示了节流器法向随机微振动的特性,为气体静压系统避开随机共振区、优化气体静压系统的设计提供了理论指导。     

Inhibition of stress corrosion cracking in 304 stainless steel through titanium ion implantation

The effects of titanium ion implantation on the stress corrosion cracking (SCC) behaviour of 304 austenitic stainless steel were studied. Slow strain rate tests (SSRTs) were conducted on 304 steel in air and in 5?wt-% NaCl solution. The microscopic effects of ion implantation were evaluated by Stopping and Range of Ions in Matter Procedures (SRIM). Fracture morphologies and microstructures were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The fracture surfaces illustrate that ion implantation significantly inhibits the corrosion pits that initiate SCC. A dense passive film, which inhibits SCC, was formed during the ion implantation process. SCC initiation was restrained due to the dense dislocation nets that were generated by titanium ion implantation.

Highlights

• Ion implantation inhibits SCC susceptibility.

• The lack of Cr at the grain boundary leads to the expansion of SCC along the grain boundary.

• Implantation-induced damage leads to high-density dislocations.

• The surface was amorphised due to high-density dislocations.

     

纳米Co/rGO磁性复合吸附材料的制备及对Cu2+的吸附性能

以改进Hummer法制备的薄片状氧化石墨烯(GO)为载体和模板负载钴离子，然后采用原位还原法制得纳米金属Co/石墨烯磁性复合吸附材料(Co/rGO)，并将其应用于对Cu2+的吸附和脱除，以期为高效可复用的铜离子脱除剂的合成与应用提供指导。实验结果证实，Co/rGO复合材料具有超顺磁性，能够很方便的使用磁铁进行分离并在无磁场情况下振荡分散。Co/rGO复合材料对Cu2+具有稳定的吸附/脱附性能，实验条件下对Cu2+的最大吸附容量达到117.5 mg/g且5 min内实现吸附平衡，远优于其原料GO的60 min吸附容量27.6 mg/g。本工作系统考察了NaOH加入量、络合剂种类、溶剂种类等关键因素对Co粒子在rGO载体上形貌和分布特性的影响，比较了不同合成条件下的复合材料对Cu2+吸附效果的影响，并对优选条件下制备的Co/rGO复合材料进行了FT-IR, XRD, SEM表征。研究结果表明，纳米Co/rGO磁性材料对Cu2+的吸附过程更符合Freundlich模型，属于多层吸附。室温下吸附焓ΔH=17.81 kJ/mol，吸附反应平衡常数Kθ=3.65。当初始Cu2+浓度为39.22 mg/L时，对Cu2+的吸附率为93.47%，五次吸附/脱附循环后吸附容量仍保持在初始值的94%，每次吸附后溶液中残余Cu2+浓度均满足钴电解液对杂质铜离子的浓度去除要求(5 mg/L)或GB 8978-1996污水综合排放标准3级(2 mg/L)，有望在相关领域发挥作用。     

A spectrally selective surface structure for combined photothermic conversion and radiative sky cooling

The sun and outer space are the ultimate heat and cold sources for the earth, respectively. They have significant potential for renewable energy harvesting. In this paper, a spectrally selective surface structure that has a planar polydimethylsiloxane layer covering a solar absorber is conceptually proposed and optically designed for the combination of photothermic conversion (PT) and nighttime radiative sky cooling (RC). An optical simulation is conducted whose result shows that the designed surface structure (i.e., PT-RC surface structure) has a strong solar absorption coefficient of 0.92 and simultaneously emits as a mid-infrared spectral-selective emitter with an average emissivity of 0.84 within the atmospheric window. A thermal analysis prediction reveals that the designed PT-RC surface structure can be heated to 79.1°C higher than the ambient temperature in the daytime and passively cooled below the ambient temperature of approximately 10°C in the nighttime, indicating that the designed PT-RC surface structure has the potential for integrated PT conversion and nighttime RC utilization.     

Fe基非晶合金增强1060铝基多层复合材料的组织与性能

采用累积叠轧焊+中间退火法复合轧制1060Al/Fe基非晶多层铝合金复合板材。利用光学显微镜、扫描电镜、X-衍射分析仪以及拉伸试验机分析Al基复合材料的微观组织结构变化、断口形貌、物相组成以及力学性能。结果表明:Fe基非晶复合材料的增强体在300 ℃中间退火过程中发生部分晶化,在累积变形轧制过程中发生破碎,并随着变形道次的增加,破碎程度随之增大;复合板前6道次的累积轧制变形出现了明显的加工软化现象,并且随着变形道次的增加,其加工软化的效果愈明显;随着累积轧制变形道次增加,Al基复合材料的力学性能发生了明显的变化,第2道次轧制变形后屈服强度与抗拉强度达到了最大值为140 MPa和156 MPa,伸长率为5.53%,达到最佳综合性能。     

微观表面形貌对螺旋槽液膜密封空化发生的影响

为探索微观表面形貌对液膜密封空化的影响,基于满足质量守恒的JFO空化模型及坐标变换,建立考虑微观表面形貌的双坝区螺旋槽液膜密封数学模型;采用有限体积法离散求解控制方程,综合分析表面粗糙度、周向波度和径向锥度对螺旋槽液膜密封空化发生的影响规律。结果表明:相比而言,密封面计入微观表面形貌后,摩擦副液膜中空穴区发生位置分散且形状不规则;以空化面积比为判据,较大表面粗糙度对液膜空化促生虽起到积极作用,但数据较小,可忽略不计;锥度对液膜中空穴促生和抑制影响有限,波幅的增加显著促进液膜中空穴的发生;高频波数时,正锥度有利于降低液膜空化面积比,抑制空穴。     

自旋对角接触球轴承弹流润滑与油膜刚度的影响

根据角接触球轴承自旋运动特征，同时考虑弹流润滑效应，建立角接触球轴承考虑自旋运动的弹流润滑模型；采用多重网格法求解弹性变形，利用有限差分法迭代求解雷诺方程，得到较为精确的数值解；分析不同赫兹接触压力、滚道表面粗糙度下自旋对角接触球轴承弹流润滑和油膜刚度的影响。结果表明：考虑自旋时随着Hertz接触压力、自旋角速度增大，油膜厚度减小，油膜压力增大，油膜承压区域呈细长状，并向接触中心靠近；随着滚道表面粗糙度幅值增大，油膜压力和膜厚均出现了波动，且考虑自旋运动时，轴承油膜厚度明显减小，油膜局部压力峰值更大；随着卷吸速度、润滑油黏度增大，油膜刚度减小，而考虑自旋运动时油膜刚度值更大；随着自旋角速度增大，油膜刚度逐渐增大。